JULY 3, 2020: We are accepting non-Weber recones again!
please visit our recone link  

Hello...

It looks like you are visiting our site on a browser that is really old. Unfortunately, this means you can't get the full experience. It'd be awesome if you could upgrade to a modern browser, especially Chrome and Firefox as that is the best out there right now.

Copyright 2014. All Rights Reserved.

    Attenuators

    Attenuators
    Show
    Set Ascending Direction

    Attach these wings to the sides of your Mass 200 attenuator, and you can mount it in a standard 19" rack. Uses three rack spaces. Must place the attenuator on the topmost spaces of the rack to allow proper ventilation.

    Rackmount Wings for the MASS 200

    Attach these wings to the sides of your attenuator, and you can mount it in a standard 19" rack. Uses two rack spaces. Must place the attenuator on the topmost spaces of the rack to allow proper ventilation.

    Rackmount Wings for the Standard MASS, MASS Lite,and MASS III Attenuators

    1/4" Male to two Female speaker cable. 10" long. 16ga wire

    Y-Cable (To connect more than one cabinet to the output of the attenuator)

    Dual male spade connectors on the cable end connect to female spade terminals on the cable that went to the speaker. The other end of that cable connects to the input of the MASS. The other cable plugs into the output of the MASS and the end of that cable is connected to the spade lugs on the speaker. Each cable is 2ft long.

    Attenuator harness for any amp that has a hard-wired speaker.

    1/4" Male to Female speaker cable. 96" long. 16ga wire

    8ft phone plug to phone jack cable

    1/4" Male to Male speaker cable. 96" long. 16ga wire

    8ft phone plug to phone plug cable

    1/4" Male to Female speaker cable. 48" long. 16ga wire

    4ft phone plug to phone jack cable

    1/4" Male to Male speaker cable. 48" long. 16ga wire

    4ft phone plug to phone plug cable

    1/4" Male to Female speaker cable. 24" long. 16ga wire

    2ft phone plug to phone jack cable

    1/4" Male to Male speaker cable. 24" long. 16ga wire

    2ft phone plug to phone plug cable

    Metal jacketed 1/4" phone plug on one end, RCA jack on other end. 1 foot length.

    1ft RCA phono jack to 1/4 phone plug (For Champs, Attenuator to Speaker)

    Metal jacketed 1/4" phone plug on one end, RCA plug on other end. 1 foot length.

    1ft RCA phono plug to 1/4 phone plug (For Champs, Amp to Attenuator)

    The two male phono plugs connect to two of the Bassman chassis phono female speaker output connectors. The other end of that cable connects to the MASS input. On the other cable, the phone plug connects to the output of the MASS and the four speaker cables from the amp plug into the four female phono connectors. Each cable is 2ft long.

    59 Bassman Attenuator Harness

    1/4" Male to Female speaker cable. 12" long. 16ga wire

    1ft phone plug to phone jack cable

    20 watt dummy load. This device is inserted inline with one or more speakers in a multi speaker cabinet. The purpose is to be able to turn off those speakers for lower volume from the amp, while retaining the proper impedance match to the amplifier.

    These are not attenuators with volume controls. They are simple on/off devices that are designed with something like a Tweed Bassman or Super Reverb in mind - where you have four 8-ohm speakers and you can put one silencer inline with each speaker you want to be able to turn off.

    Use in-line or in place of one 20w speaker

    This device is a 50 watt dummy load with a headphone output jack.The headphone jack is a stereo jack wired for mono operation. The output level to the headphones is continuously adjustable. A variable line out is also provided. The load switch switches between the normal speaker for the amplifier and the internal dummy load, which is nominally 8 ohms. Most amplifiers will tolerate a 2 to 1 impedance mismatch. The headphone output jack and its volume control are always active regardless of the position of the load switch.

    This item is hand-built to order, to ensure the best attention to detail is paid to its construction.  We build them one at a time, on a table - not hundreds at a time on an assembly line.  This allows us to reduce the margin for error and produce an overall higher-quality product.  Please allow at least 7-10 business days for your order to be built and then shipped.

    For use with up to 50w amplifiers

    Attenuators
    Show
    Set Ascending Direction